欧美日韩国产一二三四五区,国产区在线观看成人精品,91亚洲精品国产嫩草,国产丰满的富婆自拍对白,久久精品偷拍视频观看,国产av一区二区中文字幕,久久国产超碰女女av,久久不卡国产一区二区,欧美中文字幕一二三四区,亚洲欧美熟妇欲乱又伦

<delect id="d07zl"></delect>

    1. <rt id="d07zl"></rt>
        <rt id="d07zl"></rt>
        Welcome to Shenzhen Zhongyuan Plastic Co., Ltd!

        News



        Tel:(0755)27151698
        Fax:(0755)27150611
        Mailbox:szzyzcl@163.com / szzy@szzy99.com
        Add:Building A1 and A2, No.1 Industrial Zone, yuliu property company, Gongming town, Bao'an District, Shenzhen
        Industry information

        當(dāng)前位置:

        首頁 News Industry information

        Causes and solutions of top whiteness in injection molding products

        Release time:2021-08-16

        When the plastic parts of injection products are ejected from the mold, if the ejector pin is used, the ejector rod will often leave deep or shallow marks on the plastic parts. If these traces are too deep, the so-called top white phenomenon will appear. In serious cases, the so-called top explosion will occur when the plastic parts are pushed through.


        The main reason for the whiteness of plastic parts is that the product has a large mold adhesion force, and the ejection part on the plastic parts causes white marks at the ejection part of the ejector rod. The specific reasons and improvement methods are as follows:


        1. Back mold temperature is too low or too high: adjust the appropriate mold temperature.


        2. Too fast ejection speed: slow down the ejection speed.


        3. With demoulding chamfer: overhaul the mold (polishing).


        4. The ejection of finished products is unbalanced (the ejection leaf spring is broken): repair the mold (make the ejection balanced).


        5. Insufficient number of thimbles or improper position: increase the number of thimbles or change the position of thimbles.


        6. Vacuum occurs in the mold during demoulding: clean the dirt in the ejector pin hole to improve the air inlet effect.


        7. The finished bone and column positions are rough (inverted): polish each bone and column position.


        8. High injection pressure or holding pressure: reduce the pressure appropriately.


        9. The demoulding angle of the finished mold is too small: increase the demoulding angle of the rear mold.


        10. Improper action time or position of side slider: repair the mold (make the core pulling action normal).


        11. Ejection area is too small or ejection speed is too fast: increase the ejection area or slow down the ejection speed.


        12. The injection speed of the last section is too fast (Burr): slow down the injection speed of the next section.


        These are the reasons and solutions for the whitening of injection molded products.

        Copyright: Shenzhen Zhongyuan Plastic Co., Ltd. | mold processing customized manufacturer. If you want to know the processing price of the factory, how much is it, and which is good, please contact us Yue ICP Bei No. 17060480
        国产一区二区久久不卡| 国产精品久久精品女日| 国产精品喷水视频观看| 精美人妻一区二区三区| 成在线人视频免费视频| 午夜精品久久一区二区三区| 免费人妻精品一二三区| 人妖另类综合视频网站| 欧美做受又硬又粗又大视频 | 一区二区三区蜜桃91| 国产无遮挡猛进猛出的| 亚洲一级av大片在线观看| 国产精品黑丝袜白丝袜久久| 亚洲熟女黑人综合一区| 成人性生交片无码免费看| 人妻中文字幕亚洲精品| 乱女乱妇熟女熟妇妇色| 中文字幕无线码一区二区| 岛国中文字幕一区二区| 亚洲中文字幕国产精品| 国产美女在线播放91| 精品国产东北熟女露脸| 久久国产精品果冻传媒| 国产中文字幕精品在线| 亚洲欧美日韩国产大片| 成人一区二区三区av| 九九久久亚洲综合久久久| 精品一区二区蜜桃视频| 岛国精品免费在线观看| 日韩人妻系列在线视频| 人妻av丝袜诱惑一区| 国内少妇人妻偷人精品视频| 青草99在线免费观看| 中文字幕日韩欧美新片网| 国产一区二区三区爆白浆| 亚洲精品国产品国语原创| 91人妻专区久久综合网欧美色妞| 日韩精品欧美亚洲一区二区| 日韩精品一区二区三区四区五区六| 国产成人精品一 二区| 亚洲妇女av一区二区|