欧美日韩国产一二三四五区,国产区在线观看成人精品,91亚洲精品国产嫩草,国产丰满的富婆自拍对白,久久精品偷拍视频观看,国产av一区二区中文字幕,久久国产超碰女女av,久久不卡国产一区二区,欧美中文字幕一二三四区,亚洲欧美熟妇欲乱又伦

<delect id="d07zl"></delect>

    1. <rt id="d07zl"></rt>
        <rt id="d07zl"></rt>
        Welcome to Shenzhen Zhongyuan Plastic Co., Ltd!

        News



        Tel:(0755)27151698
        Fax:(0755)27150611
        Mailbox:szzyzcl@163.com / szzy@szzy99.com
        Add:Building A1 and A2, No.1 Industrial Zone, yuliu property company, Gongming town, Bao'an District, Shenzhen
        Industry information

        當(dāng)前位置:

        首頁 News Industry information

        Cause analysis and solution of cracking of plastic shell products

        Release time:2021-11-12

        Engineering plastics are widely used in manufacturing industrial parts and various shells because of their excellent properties - high strength, heat resistance, impact resistance, aging resistance and so on. But the cracking of plastic products is also a headache, which is caused by mold, molding process, plastic material, environmental stress and so on. Today, we will discuss the causes and solutions of plastic products cracking.


        1、 Analysis of cracking causes and suggestions for improvement

        Different cracking causes will lead to different types of cracking. According to the cracking conditions encountered in the actual development process, there are usually four kinds of cracking phenomena of plastic products:

        1. Demoulding cracking, when plastic products come out of the mold, they crack directly, and the causes and consequences of this kind of cracking are relatively easy to predict;

        2. Reliability test cracking, such as local cracking or cracks after the completion of drop test, environmental test and twist test;

        3. The product cracks during assembly;

        4. Application cracking, the cracking of products after being placed for a period of time or during use, is often difficult to predict, and the consequences may be devastating.

        The above cracking conditions have internal and external causes, and the same reasons; In view of the above problems, we comprehensively analyze the main factors affecting product cracking from the following aspects;


        2、 Influence of product design

        1. The product wall thickness is too large, and local shrinkage is serious;

        2. During the design, the partial bone position of the product is too thin to bear large impact force;

        3. The design strength of the whole machine is too weak and there are too few stiffeners;

        4. There are too many sharp corners inside the product, and the glue doesn't go smoothly during injection molding. It is better to use fillet transition to reduce the risk of cracking due to stress concentration;


        3、 Influence of mold design

        1. The rubber inlet is too large;

        2. The gate design and distribution are unreasonable, which is easy to form fusion lines, and the product strength near the fusion lines is weak;

        3. The design of the cooling system is unreasonable, and local supercooling or overheating causes stress contraction;

        4. Insufficient demoulding slope;

        5. Poor mold cavity design (internal stress concentration);

        6. Insufficient exhaust;

        7. The ejection of the product is unbalanced, and it is easy to crack due to local stress during ejection;

        8. The surface of the mold is too rough.


        4、 Influence of injection molding process

        1. Excessive material measurement.

        2. The resin temperature is too low.

        3. Mold temperature is too low.

        4. If the injection pressure is too high or too low, it will affect the product strength. If the pressure is too high, the product structure near the gate will become brittle due to high stress. If the pressure is too low, the strength of the joint line at the end of the product flow will become weak, and the product is also easy to crack. It is suggested to adjust it according to the mold flow analysis data.

        5. The injection holding pressure is too high.

        6. The shooting time is too long.

        7. Ejection speed is too fast or too slow.


        5、 Influence of plastic raw materials

        1. This material contains volatiles;

        2. Mix and match of different materials;

        3. The material is not dry;

        4. Excessive nozzle material is added;

        5. The surface technology in surface treatment will corrode the products, and cracks will appear after a long time;

        There are many factors that affect the cracking of injection molded products, which should be comprehensively analyzed and considered. Many factors restrict each other. Product design should be reviewed in advance together with mold design, so as to make reasonable tradeoffs, solve problems and improve quality.

        Copyright: Shenzhen Zhongyuan Plastic Co., Ltd. | mold processing customized manufacturer. If you want to know the processing price of the factory, how much is it, and which is good, please contact us Yue ICP Bei No. 17060480
        中文字幕乱码亚洲三区| 中文字幕欧美精选国内精品 | 国内揄拍高清国内精品情侣| 亚洲成人有码免费在线| 亚洲精品综合中文字幕| 国产精品无码一本二本三本色| 四虎永久精品免费视频| 亚洲综合色自拍一区| 日韩欧洲在线高清一区| 爽爽午夜福利一区二区| 久久天天躁狠狠躁夜夜躁2014| 中文字幕一区二区日韩| 国产精品人人做人人爱| 一本久道久久综合狠狠操| 精品少妇后入一区二区三区| 亚洲国产精品懂色av| 丰满高潮美女后入极品少妇| 亚洲一区二区三区在线观看| 成人女同av免费观看| 国产裸拍裸体视频在线观看| 日本在线免费中文字幕| 日日狠日| 91人妻人妻综合精品| 久久久噜噜噜久久中文字幕色伊伊 | 成人免费视频自偷自拍| 激情内射人妻一区二区| 欧美精品网站一区在线观看| 国产精品久久久久久久久岛国| 精品综合亚洲中文字幕| 女同性恋亚洲一区二区 | 色天天综合天天综合网| 亚洲乱码一区二区三区精品| 亚洲AV无码片在线观看| 亚洲狠狠久久婷婷激情| 亚洲中码中文字幕人妻| 国产免费人成网站在线播放| 爽人爽人妻爽人妻爽人| 日韩欧美国产成人在线| 国产最新av在线播放| 国产精品亚洲中文字幕| 成人av在线一区二区|