欧美日韩国产一二三四五区,国产区在线观看成人精品,91亚洲精品国产嫩草,国产丰满的富婆自拍对白,久久精品偷拍视频观看,国产av一区二区中文字幕,久久国产超碰女女av,久久不卡国产一区二区,欧美中文字幕一二三四区,亚洲欧美熟妇欲乱又伦

<delect id="d07zl"></delect>

    1. <rt id="d07zl"></rt>
        <rt id="d07zl"></rt>
        Welcome to Shenzhen Zhongyuan Plastic Co., Ltd!

        News



        Tel:(0755)27151698
        Fax:(0755)27150611
        Mailbox:szzyzcl@163.com / szzy@szzy99.com
        Add:Building A1 and A2, No.1 Industrial Zone, yuliu property company, Gongming town, Bao'an District, Shenzhen
        Industry information

        當(dāng)前位置:

        首頁(yè) News Industry information

        Reasons for cracking of plastic shell

        Release time:2022-03-24

        The cracking of plastic injection products includes filiform cracks, microcracks, white tops and cracks on the surface of plastic shell, as well as the trauma crisis caused by part sticking and runner sticking. According to the cracking time, it can be divided into demoulding cracking and application cracking. It is mainly caused by the following reasons:


        1. Processing

        (1) Too much processing pressure, too fast speed, more filling materials, and too long injection pressure holding time will cause excessive internal stress and cracking.

        (2) Adjust the mold opening speed and pressure to prevent demoulding cracking caused by rapid and strong tensile parts.

        (3) Properly increase the mold temperature to make the parts easy to demould, and appropriately reduce the material temperature to prevent decomposition.

        (4) Prevent cracking due to weld lines and plastic degradation, thereby reducing mechanical strength.

        (5) Use release agent properly, and pay attention to often eliminate aerosols and other substances attached to the surface of the mold.

        (6) The residual stress of the plastic shell can be eliminated by annealing heat treatment immediately after forming, so as to reduce the occurrence of cracks.

        圖片4-2.png


        2. Mold aspect

        (1) The ejection should be balanced, such as the number and cross-sectional area of ejector pins should be sufficient, the demoulding slope should be sufficient, and the surface of the cavity should be smooth enough to prevent the residual stress concentration of ejection from cracking under external forces.

        (2) The plastic shell structure should not be too thin, and the transition part should adopt arc transition as far as possible to avoid stress concentration caused by sharp corners and chamfers.

        (3) Try to use less metal inserts to prevent the internal stress from increasing due to the different shrinkage of the plastic shell of the inserts.

        (4) The deep bottom plastic shell should be equipped with appropriate demoulding air inlet channels to prevent the formation of vacuum negative pressure.

        (5) The sprue is large enough to demould the gate before solidification, which is easy to demould.

        (6) The connection between the sprue bushing and the nozzle should prevent the plastic shell from sticking to the fixed mold due to the dragging of cold and hard materials.


        3. Material aspect

        (1) The content of recycled materials is too high, which leads to the low strength of the plastic shell.

        (2) The humidity is too high, which makes some plastics react with water vapor, reduces the strength, and causes the plastic shell to eject and crack.

        (3) The material itself is not suitable for the processing environment or the quality is poor, and the plastic shell is polluted, causing cracking.


        4. Machine

        The plasticizing capacity of the injection molding machine should be appropriate. If the plasticizing capacity is too small and insufficient, it will become brittle without sufficient mixing, and if it is too large, it will degrade.


        5. Technical aspects

        Improper process selection, such as too high material temperature, too high back pressure, too fast glue melting, etc., leads to the decline of physical properties.

        Copyright: Shenzhen Zhongyuan Plastic Co., Ltd. | mold processing customized manufacturer. If you want to know the processing price of the factory, how much is it, and which is good, please contact us Yue ICP Bei No. 17060480
        久久精品一区二区熟女| 少妇人妻偷人偷人精品| 亚洲精品蜜臀视频在线| 久久中文字幕成熟人妻| 一区二区三区国产在线网站视频| 色综合久久五月天久久久| av在线一区二区播放| 99久久国产一区二区三区| 国产成人无码精品久久二区三区| 亚洲综合图区中文字幕| 欧美在线视频一区二区三区| 国产精品传媒一区二区| 欧美日韩亚洲人妻在线| 国内自拍视频在线观看| 四虎永久免费一级黄片| 国产日韩亚洲av高清在线不卡| 日韩视频香蕉在线观看| 激情综合网激情五月婷婷色狠| 国产精品亚洲一区二区三区正片| 艳妇乳肉豪妇荡乳AV无码福利| 日韩有码中文字幕一区八戒| 日韩av经典一区二区| 操到高潮喷水在线观看| 国产福利主播一区二区| 青草视频午夜在线观看| 亚洲综合中文字幕一区| 国产欧美一区二区三区在线播放| 亚洲AV色香蕉一区二区三区 | 婷婷丁香久久日本欧美| 国内色精品视频在线网址| 午夜精品福利亚洲国产| 天天做天天摸天天爽天天爱| 国产精品一区日本技女| 国产成人艳妇AA视频在线 | 精品久久久噜噜噜久久久| 91黄色大全免费观看| 91人妻人妻综合精品| 久久精品国产亚洲av高清不卡一| 人妻在线有码中文字幕| 国产精品剧情一区二区在线观看| 可以看到国产日韩精品|